Bathtub Reglazing in Culver City, CA
Restore a chipped, stained or dated bathtub to a glossy, like-new finish in a single visit. Local technicians, 10+ years of experience, and a 2-year written warranty on every tub.
Culver City's Original Tubs Deserve a Second Life
Much of Culver City was built out between the 1920s and 1960s, which means thousands of homes in Carlson Park, Sunkist Park, Blair Hills and Lucerne-Higuera still have their original cast iron or porcelain-enameled tubs. Those tubs are heavier and better made than most modern replacements, but 60-plus years of Los Angeles hard water, abrasive cleaners and daily use leave them dull, rough and stained.
Bathtub reglazing (also called bathtub refinishing or resurfacing) strips the failing surface, repairs chips and rust spots, and applies a new commercial-grade coating that bonds to the tub. The result looks and cleans like a brand new tub, without touching the plumbing, the tile or the walls.
- Cast iron, porcelain, steel, fiberglass and acrylic tubs
- Chip, crack and rust-spot repair included
- Clawfoot and alcove tubs, soaking tubs and tub-shower combos
- Color changes: pink, mint and yellow tubs to modern white
- Non-slip bottom available for seniors and kids
- Ready to use in 24 hours
What Happens When We Reglaze Your Bathtub
Every job follows the same careful preparation, because preparation is what makes a reglazed tub last. Here is exactly what our technicians do in your Culver City bathroom.
1. Protection and cleaning
We mask the surrounding tile, floor and fixtures, set up ventilation, and clean the tub with a commercial degreaser to remove soap scum, body oils and silicone residue that would prevent adhesion.
2. Surface repair
Chips, cracks, rust around the drain and worn-through enamel are filled and sanded flush. Old caulk is removed and the drain and overflow trim are pulled or masked so the finish wraps cleanly.
3. Etching and bonding
The tub is chemically etched and sanded, then a bonding agent is applied. This step is skipped by low-cost operators and is the number one reason reglazed tubs peel.
4. Spray application
Three to four thin coats of a low-VOC, hospital-grade aliphatic urethane are sprayed with HVLP equipment. The coats level into a smooth, high-gloss surface with no brush marks.
5. Cure, caulk and clean up
We re-caulk the tub, remove all masking, and leave the bathroom clean. Most tubs take 3–5 hours on site and are ready for water after 24 hours.
This service is covered by our 2-year written warranty against peeling, bubbling and adhesion failure. Kitchen sinks are the one exception: they carry a 6-month warranty because of the heavy daily use they take. Full terms are on our Terms of Service page.
What Bathtub Reglazing Costs in Culver City
Replacing means demolition, disposal, a plumber, possibly a Culver City building permit, and days without a working bathroom. Reglazing restores the surface you already own in one visit.
| Reglazing | Full Replacement | |
|---|---|---|
| Typical cost | $350 – $650 | $2,500 – $6,000+ |
| Time on site | Hours | 2–5 days |
| Demolition & dust | None | Yes |
| Plumbing / permit | Not required | Often required |
| Typical savings | Up to 80% less than replacing | |
Ranges reflect typical Westside Los Angeles projects and are for guidance only. Every job is quoted individually after we see the surface.
See the Full Savings Breakdown
Bathtub Reglazing in Four Simple Steps
Free quote
Send photos through our quote form or call. Most Culver City quotes go out the same day.
Protect & prep
We mask the room, strip old coatings, repair chips and cracks, and etch the surface so the new finish bonds permanently.
Spray the new finish
Multiple coats of a commercial-grade, low-VOC urethane are applied with a fine-finish spray system for a smooth, glossy result.
Cure & enjoy
The surface is ready for normal use in 24 hours. We leave the space clean and walk you through simple care.
Bathtub reglazing Across Every Culver City Neighborhood
We are based in Culver City (ZIP codes 90230 and 90232) and schedule most local jobs within a few days.
Culver City neighborhoods we serve
- Blair Hills
- Blanco / Culver Crest
- Carlson Park
- Clarkdale
- Culver West
- Downtown Culver City
- Fox Hills
- Hayden Tract
- Jefferson
- Lindberg Park
- Lucerne-Higuera
- McManus
- Park East
- Park West
- Rancho Higuera
- Studio Village
- Sunkist Park
- Veterans Park
- Washington Culver
Nearby Westside communities
- Mar Vista
- Palms
- Playa Vista
- Westchester
- Marina del Rey
- Del Rey
- Cheviot Hills
- Baldwin Hills
- Ladera Heights
- Beverlywood
- West Los Angeles
- Venice
Bathtub Reglazing FAQs
Answers to the questions Culver City homeowners and landlords ask us most.
How much does bathtub reglazing cost in Culver City?
Most standard bathtubs in Culver City are reglazed for a few hundred dollars, a fraction of the several thousand dollars a replacement typically costs once demolition, plumbing, tile repair and disposal are added. Send photos through our quote form for an exact price.
How long does the tub need to cure before I can use it?
We ask that you keep the tub dry for 24 hours. After that it is ready for a normal bath or shower. Avoid bath mats with suction cups for the first week while the finish fully hardens.
Can you reglaze a cast iron or porcelain tub from the 1940s or 50s?
Yes. Original cast iron and porcelain tubs in Culver City's older homes are ideal candidates. They are structurally sound, and reglazing restores the smooth, bright surface that decades of hard water and cleaning products wore away.
Will the new finish look like paint?
No. We spray a professional urethane coating in several thin coats, which levels into a glossy, porcelain-like surface. Properly prepared and applied, it looks and feels like a new tub.
Can I change the color of my bathtub?
Absolutely. Most customers choose bright white or biscuit, but we can color-match almond, bone or a custom shade to coordinate with existing tile.
Does bathtub reglazing come with a warranty?
Yes. Every bathtub we reglaze is covered by a 2-year written warranty against peeling, bubbling and adhesion failure.
Other Reglazing Services in Culver City
Doing more than one surface on the same visit is the most cost-effective way to update a whole bathroom.
Sink Reglazing
Bathroom and kitchen sinks refinished in the color you want, with no plumbing changes.
Learn moreShower Reglazing
Shower pans, walls and surrounds sealed into one smooth, mildew-resistant surface.
Learn moreFiberglass Bathtub Enclosure Reglazing
One-piece fiberglass and acrylic tub-shower units repaired and recoated instead of ripped out.
Learn moreTile Walls & Floors Reglazing
Pink, mint and yellow mid-century tile updated to a modern color without demolition.
Learn moreReady to Love Your Bathtub Again?
Free, no-obligation quotes for Culver City and the Westside. Most tubs are finished in one visit and covered for 2 years.